Microcontroller Kits
Programmer and Target 89s51

Simple Mikrokontroller 89s51 Trainer


Standart
Mikrokontroller 89s51 Trainer


Super Mikrokontroller Trainer 89s51

+

All Item Include

Programmer
Via USB

4.3. Taking data of DIP Swicht serially.- Serial RS232

Communication standart using serial data RS232 is very efective way to minimize cable connection. This experiment, will be done by intake of data of DIP Swicht serially with using serial data communications RS232.

Figure 4.1. Sending data DIP swicht serially to PC

Step 1st
Build the circuit as shown in figure 4.1. As you seen on figure 4.1. Remember, that all we want to do with this lesson is take data DIP SW trough PC serially.

Step 2nd
In this step, you must tipe the assembly program to make your serial working, we assume that you have already known the editor, we used MIDE-51 to edit the program. ( Download File asm and hex : dip_sw.zip, Download File Complete Circuit File : SerialDipSW)

        org 0h
        nop
        call initserial
gets:   call inchar
        mov P2,a
        sjmp gets
;
initserial:
        mov scon,#52h
        mov tmod,#20h
        mov th1,#-13
        setb tr1
        ret
;
inchar:
        detect: jnb ri,detect;
        clr ri
        mov a,sbuf
        ret
;
End

To get the data from microcontroller serially, computer must run the program to get data from port communication RS232, in this experiment I have been used Delphi programming: ( Download File Delphi : dipsw.zip )

(a)

(b)
Figure 4.2. Delphi Programming Display Data DIP SW

var
    Form1: TForm1;
    data,status:byte;
const
    base = $3f8;{base address port serial}
    lcr = 3; {line control register}
    dll = 0; {divisor lacht low byte}
    dlh = 1; {divisor lacht high byte}
    lsr = 5; {line status register}
Procedure Initserial;
begin
    asm
        mov dx,base+lcr; {address line control register}
        mov al,$80 ; {10000000b = access bit divisor lacht}
        out dx,al
;
        mov dx,base+dll; {address divisor lacht low byte}
        mov al,$30 ; {DLLB = 30h}
        out dx,al
;
        mov dx,base+dlh; {address divisor lacht high byte}
        mov al,$00     ; {DLLH = 00h}
        out dx,al
;                       {In this case Port Serial have}
;                       { baud rate = 2400 bps}
        mov dx,base+lcr;{address line control register}
        mov al,$03 ;    {00000011b =}
        out dx,al ;     {bit 7=0, access to Rx buffer & Tx
;                       {bit 6=0, set break disable
;                       {bit 5-4-3=000, no parity
;                       {bit 2=0, one stop bit
;                       {bit 1-0=11,data lenght 8 bit}
        end;
end;
;
Procedure Receive_Data_Serial;
begin
 asm
  mov dx,base
  in al,dx
  mov data,al
 end
end;
;
procedure TForm1.FormCreate(Sender: TObject);
begin
  Initserial;
end;
procedure TForm1.Button1Click(Sender: TObject);
begin
 initserial;
 timer1.enabled:=true;
end;

procedure TForm1.Timer1Timer(Sender: TObject);
begin
 Repeat
  asm
   mov dx,base+lsr; { address line status register }
   in al,dx
   and al,$01 ; {LSR = 00000001b, deteksi bit 0}
   mov status,al ; {bit 0 = data ready}
  end;
 until status = $01 ;{ jika bit 0 = 1 then data ready}
 Receive_Data_Serial;
 edit1.text:=inttostr(data);
end;

Step 3rd
Safe your assembly program above, Compile the program that you have been save by using MIDE-51, see the software instruction.

Step 4th
Download your hex file (dip_sw.hex ) into the microcontroller by using Microcontroller ATMEL ISP software, see the instruction.After download this hex file you'll see the action of serial transmition( of course if your cable connection and your program are corrected ).

Comments, questions and discussion about this topic

BACK NEXT