|
Pelatihan
Dasar Mikrokontroller
14-15 April 2007
Surabaya
Rp. 300.000
Microcontroller Kits
Programmer
and Target 89s51
Rp.100.000
(USD $10)
Simple
Mikrokontroller 89s51 Trainer
Rp, 350.000
(USD $35)
Standart
Mikrokontroller 89s51 Trainer
Rp. 650.000
(USD $65)
Super
Mikrokontroller Trainer 89s51
Rp.1.250.000
(USD $125)
 |
|
NEXT
3. Timer/ Counter
The MCS-51 has two 16 bit Timer/ Counter register. Timer
0 and Timer 1. Both can be configured to operate either as timers or
event counters ( see figure 3.1. ).
In the Timer function, the register is incremented every mechine cycle.
Figure 3.1. Diagram block Timer/ Counter Operation
As shown in figure 3.1., microcontroller can be used
as timer or counter as you need. The question is, what you have to do,
so the microcontroller will act as timer or counter. See left and right
swicht on diagram blog. Microcontroller will act as timer when swicht
position on upper and microcontroller will act as counter when swicht
position on lower by controlling C/T bit on TMOD register. The right swicht
position is depent on BIT GATE ( Register TMOD ), TR1 ( Register TCON
) dan INT1.
Timer/ Counter Mode Control ( TMOD ) Register
TIMER 1 |
TIMER 0 |
GATE |
C/T |
M1 |
M0 |
GATE |
C/T |
M1 |
M0 |
GATE |
Gating control when set. Timer/
Counter X is enabled only while INTx pin is high and TRx control
pin is set |
C/T |
Timer or Counter Selector cleared for Timer
operation (input from internal system clock) and set for counter
operation (input from Tx input pin) |
M1 |
M0 |
Operating |
0 |
0 |
8048 Timer, TLx serves as 5 bit prescaler |
0 |
1 |
16 bit Timer/Counter THx and TLx are cascaded,
there is no prescaler |
1 |
0 |
8 bit auto reaload Timer/ Counter THx holds
a value which is tobe reloaded into TLx each time it overflows |
1 |
1 |
(Timer 0) TL0 is an 8 bit Timer/ Counter controlled by the standard
timer 0 control bits
(Timer 1) Timer/ Counter 1 stopped |
Timer/ Counter Control ( TCON ) Register
MSB |
|
LSB |
TF1 |
TR1 |
TF0 |
TR0 |
IE1 |
IT1 |
IE0 |
IT0 |
BIT |
SYMBOL |
FUNCTION |
TCON.7 |
TF1 |
Timer 1 overflow flag. Set by hardware on Timer/Counter
overflow. Cleared by hardware when processor vector to interrupt
routine, or clearing the bit in software. |
TCON.6 |
TR1 |
Timer 1 Run control bit . Set/ cleared by software
to turn Timer/ Counter on/off |
TCON.5 |
TF0 |
Timer 0 overflow flag. Set by hardware on Timer/Counter
overflow. Cleared by hardware when processor vector to interrupt
routine, or clearing the bit in software. |
TCON.4 |
TR0 |
Timer 1 Run control bit . Set/ cleared by software
to turn Timer/ Counter on/off |
TCON.3 |
IE1 |
Interrupt 1 Edge flag. Set by hardware when
external interrupt edge detected. Cleared when interrupt processed. |
TCON.2 |
IT1 |
Interrupt 1 type control bit. Set/ cleared
by software to specefy falling edge/ low level trigerred external
interupts |
TCON.1 |
IE0 |
Interrupt 0 Edge flag. Set by hardware when
external interrupt edge detected. Cleared when interrupt processed. |
TCON.0 |
IT0 |
Interrupt 0 type control bit. Set/ cleared by software to specefy
falling edge/ low level trigerred external interupts |
Comments,
questions and discussion about this topic
NEXT
|
|
Programmer
ISP
89s
Free Software
a. Edsim 51
b. MIDE-51
c. ATMEL ISP
Lesson 1:
Architecture
1.1.Memory
1.2.SFR
1.3.Addressing
1.4.Instruction
Set
1.5.Assignment
Lesson 2:
Input Output
2.1.LED
2.2.Swicht
2.3.7
Segmen
2.4.LCD
Character
2.5.ADC
2.6.DAC
2.7.Motor
Stepper
2.8.Keypad
2.9.Assignment
Lesson 3:
Timer Counter
3.1.Basic
3.2.Mode
0
3.3.Mode
1
3.4.Mode
2
3.5.Mode
3
3.5.Assignment
Lesson 4:
Serial Comm.
4.1.Basic
4.2.LED
4.3.Rotate
LED
4.2 ADC
4.3.LCD
4.4.Assignment
Lesson 5:
Interuption
5.1.Basic
5.2.Timer
5.2.External
5.3.Assignment
|
